Menu
Search
Filters
Close
Menu

Currie HD60 - Mercedes Sprinter Rear Axle Assembly

Get ready to supercharge your Mercedes 2500 Sprinter Van with the ultimate upgrade - the Currie HD60 rear axle assembly. Built for strength, durability, and off-road prowess, the HD60 axle features our heavy-duty 60-series center section, robust 3.5-inch diameter axle tubes, an Eaton electric locking differential, and upgraded 35-spline chromoly axles. Moreover, the HD60 keeps your factory Mercedes OE rear brake assembles and wheel bolt pattern intact, so you can hold onto those sleek wheels.


Details:

  • Bolt in Fit for 2019-Newer 2WD and 4WD 2500 Sprinter Vans
  • Heavy-Duty 60-Series Low-Pinion Center Section
  • 3.5 x .375-inch DOM Axle Tubes
  • 35-Spline Chromoly Axles
  • 4.10 Gear Ratio
  • Eaton Electric Locking Differential
  • Currie Heavy-Gauge OE Fitment Brackets
  • Currie Rock-Proof Nodular Iron Differential Cover
  • Satin Black Powder Coat for Long Lasting Protection
  • Retains The Vehicles Factory Wheel Bearings and 6x130 Wheel Bolt Pattern
  • Retains the Vehicles Factory Rear Brake Components
  • See notes below for additional details

SKU: CE-C60LPSV410
Estimated Lead Time: 4 week(s)
$6,950.00

The Currie HD60 low-pinion rear axle for the 2019 and newer 2500 Sprinter Vans is a direct bolt-in axle assembly with all required brackets and mounts in place. The vehicle's factory wheel bearings and brakes will be retained and installed on the new HD60 axle.

 

 

Product Features:

 

Currie HD60

Designed and optimized using computer simulation, the HD60 is reinforced in critical areas with thicker walls and heavier webbing to deliver maximum strength, durability, and rigidity

Axle Tubes

Large 3.5 in. diameter .375 wall axle tubes (left) are more than 2x the strength of the stock tubes (right) without being overweight or sacrificing ground clearance

Chromoly Axles

35-spline chromoly full-floating axles (right) are 1.5x the strength of OE factory axles

Pinion Yoke

The upgraded 1350 pinion yoke provides increased strength and reliability over the failure-prone factory CV Joint

Laser Cut Brackets

Currie heavy-duty laser cut brackets provide increased strength and maintain compatibility with stock and aftermarket suspension components

Iron Cover

Currie rock-proof nodular iron cover protects expensive internals and adds structural support to the housing's face flange

Powder Coat Finish

UV Stable Satin black powder coat finish adds long-lasting protection against rust and corrosion to keep your Currie HD60 looking its best

 

 

Notes

ABS Sensors: Does not include ABS sensors; the factory sensors from the stock axle must be retained and installed on the Currie Axle

Driveshaft: The vehicle's factory driveshaft will be retained and reused with this Currie axle

Brake Components: Retains the vehicle's factory rear brake components, reuse the stock rotors and calipers from the vehicle

Wheel Bearings: Retains the vehicle's factory wheel bearings after removal of the factory axle from the bearing

Overall Width: Axle is built to match the factory width between wheel mounting surfaces

The Currie HD60 low-pinion rear axle for the 2019 and newer 2500 Sprinter Vans is a direct bolt-in axle assembly with all required brackets and mounts in place. The vehicle's factory wheel bearings and brakes will be retained and installed on the new HD60 axle.

 

 

Product Features:

 

Currie HD60

Designed and optimized using computer simulation, the HD60 is reinforced in critical areas with thicker walls and heavier webbing to deliver maximum strength, durability, and rigidity

Axle Tubes

Large 3.5 in. diameter .375 wall axle tubes (left) are more than 2x the strength of the stock tubes (right) without being overweight or sacrificing ground clearance

Chromoly Axles

35-spline chromoly full-floating axles (right) are 1.5x the strength of OE factory axles

Pinion Yoke

The upgraded 1350 pinion yoke provides increased strength and reliability over the failure-prone factory CV Joint

Laser Cut Brackets

Currie heavy-duty laser cut brackets provide increased strength and maintain compatibility with stock and aftermarket suspension components

Iron Cover

Currie rock-proof nodular iron cover protects expensive internals and adds structural support to the housing's face flange

Powder Coat Finish

UV Stable Satin black powder coat finish adds long-lasting protection against rust and corrosion to keep your Currie HD60 looking its best

 

 

Notes

ABS Sensors: Does not include ABS sensors; the factory sensors from the stock axle must be retained and installed on the Currie Axle

Driveshaft: The vehicle's factory driveshaft will be retained and reused with this Currie axle

Brake Components: Retains the vehicle's factory rear brake components, reuse the stock rotors and calipers from the vehicle

Wheel Bearings: Retains the vehicle's factory wheel bearings after removal of the factory axle from the bearing

Overall Width: Axle is built to match the factory width between wheel mounting surfaces

Customers Also Purchased
Currie Corona Tee - Front

Currie "Corona" T-Shirt

$20.00 $10.00

Details:

  • Men's White Short Sleeve Crew Neck
  • Solid Color
  • Front Logo Graphic Print
Womens Braid - Front

Currie "Braid" Womens V-Neck Tank Top

$15.00

Details:

  • Women's Lilac Tank Top
  • Scoop Neckline
  • White Graphic
  • Logo Graphic Print Front
Currie Performance Tee - Front

Currie "Performance" T-Shirt

$20.00

Details:

  • Men's Black Short Sleeve Crew Neck
  • Solid Color
  • Logo Graphic Print Front and Back
Currie Emblem Hoodie - Front

Currie "Emblem" Hoodie

$25.00

Details:

  • Men's Black Hooded Pullover Sweatshirt
  • Adjustable Drawstring Hood
  • Cuffed Long Sleeves
  • Kangaroo Pouch Pocket
  • Logo Graphic Print Front and Back





Categories
Popular tags
Contacts
  • +1 714-528-6957
  • +1 (Fax) 951-549-0267
Information
Copyright © 2024 Currie 4x4. All rights reserved.