97-06 Jeep Wrangler TJ/LJ

Currie high-strength nodular iron covers for the Jeep Wrangler TJ. Protect expensive internals from the most extreme trail hazards and adds structural support to the housing's face flange for improved strength. The clean, trim shape has ample clearance for front or rear applications where steering or gas tank clearance is a concern.

Details:

• High-Strength Nodular Iron for Maximum Protection
• Thick Reinforced Bottom Edge with Recessed Hardware
• Available for Front and Rear Axle Applications
• Choice of Red or Black Powder Coat or Raw Finish
• Includes Mounting Hardware and RTV Sealant

The Currie 44 front axle assembly for Jeep TJ/LJ/XJ vehicles is a direct bolt-in assembly with superior strength in a lightweight package designed for heavy off-road use. The Currie 44 is designed for heavy off-road with up to 37-inch tall tires and features a significantly stronger center casting, axle tubes, forged knuckles, and chromoly axles, the Currie 44 is ready for off-road adventure.

Currie 44 Features:

• Direct Bolt-in Fit for Wrangler TJ/LJ/XJ
• Stock TJ 60.5 in. Overall Width
• Currie High-Pinion Reinforced Center Section
• 3 in. Diameter, .5 in. Wall DOM Axle Tubes
• Currie Forged TJ Inner Knuckles
• 4340 Chromoly Inner and Outer Axles
• Steering Geometry and Brackets Setup for Stock Height or Lifted Vehicles
• Satin Black Powder Coat Finish for Long Lasting Protection
• Retains the Vehicle's Stock Tie Rod, Steering Knuckle Assemblies, Brakes, and Wheels

*** SELECT OPTIONS TO BUILD AND PRICE ***

The Currie 44 Hybrid front axle assembly for Jeep TJ/LJ vehicles features additional width and larger JK inner knuckles for superior strength and tire clearance in a lightweight package. The Currie 44 is designed for heavy off-road with up to 37-inch tall tires and features a significantly stronger center casting, axle tubes, JK forged knuckles, and chromoly axles, the Currie 44 is ready for off-road adventure.

Currie 44 Features:

• Currie TJ Brackets for a Direct Bolt-in Fit
• JK Width 65.375 in. Width (+ 4.9 in. )
• Currie High-Pinion Reinforced Center Section
• 3 in. Diameter, .5 in. Wall DOM Axle Tubes
• Currie Forged JK Inner Knuckles
• 4340 Chromoly Inner and Outer Axles
• Steering Geometry and Brackets Setup for Stock Height or Lifted Vehicles
• Satin Black Powder Coat Finish for Long Lasting Protection
• Requires Additional Components - See Notes below

*** SELECT OPTIONS TO BUILD AND PRICE ***

The Currie 44 for 1997 thru 2006 Wrangler TJ and LJ provide a significant strength and performance upgrade over the factory Dana 35/44 series axles at a price point that won't break the bank. With its substantially reinforced nodular iron center section, heavy-duty 3-inch x .375 axle tubes, and chromoly axles, the Currie 44 is ready for off-road adventure.

Details:

• Direct Bolt-in Fit for Wrangler TJ and LJ
• Factory 60.50 in. Width and 5 x 4.5 In. Wheel Bolt Pattern
• Low-Pinion Massively Reinforced Center Section
• 3-inch Diameter x .375 Wall DOM Axle Tubes
• Larger, Stronger JK 44 Ring and Pinion Gears
• Currie Performance 30 or 35-Spline Chromoly Axles (Dependent on Locker)
• Choice of Gear Ratio and Selectable Locker
• Retains the Factory Brakes, Wheel Bolt Pattern, and Driveshaft
• Satin Black Powder Coat Finish For Long Lasting Protection

*** CONFIGURE OPTIONS TO BUILD AND PRICE ***

The Currie 60 complete bolt-in rear performance axle assembly for the 1997-2006 Jeep TJ and LJ features a high-pinion design and exclusive rotated center section, a combination that delivers superior driveshaft clearance and obstacle slide-over with a healthy dose of strength. If you seek out the most challenging routes and toughest obstacles to conquer, the Currie 60 axle is a natural choice.

Details:

• Complete Currie 60 High-Pinion Rear Axle with 11 in. Explorer

  Disc Brakes with Internal Parking Brake

• Factory 60.50 in. Width and 5 x 4.5 In. Wheel Bolt Pattern
• High-Pinion Design Raises the Driveshaft by 2-Inches to

  Reduce Driveline Angle and Improve Clearance

• Rock Slider Low-Friction Skid Plate Sides Over Trail Obstacles with Ease
• Currie 35-spline Semi-Float Axles
• 3 in. Diameter x .5 in. Wall DOM Axle Tubes
• Choice of Gear Ratio, Axle Spline and Locker
• Satin Black Powder Coat Finish For Long Lasting Protection

*** CONFIGURE OPTIONS TO BUILD AND PRICE ***

Currie HD60 Hybrid axle assembly for the 1997-2006 Jeep TJ/LJ incorporates the unmatched strength of the Currie HD60 casting with an additional 5 inches of width, JK housing ends, and TJ bracketry. The high-pinion design and exclusive rotated center section of the HD60 provide superior driveshaft clearance and obstacle slide-over for enhanced performance. If you enjoy tackling challenging routes and formidable obstacles, the Currie HD60 axle is ideal.

Details:

• Complete Currie HD60 High-Pinion Rear Axle

• Currie TJ Brackets Installed
• JK 65.375 in. Width (+4.9 in.)
• JK 5 x 5 Wheel Bolt Pattern
• High-Pinion Design Raises the Driveshaft by 2-Inches to

  Reduces Driveline Angle and Improve Clearance

• Rock Slider Low-Friction Skid Plate Sides Over Trail Obstacles with Ease
• Currie 35-spline Semi-Float Axles
• 3 in. Diameter x .5 in. Wall DOM Axle Tubes
• Choice of Gear Ratio, Axle Spline and Locker
• Satin Black Powder Coat Finish For Long Lasting Protection
• Requires Additional Components - See Notes Below

*** CONFIGURE OPTIONS TO BUILD AND PRICE ***